Our new brochure has arrived! Download your copy here.

How To Fit Wall Panelling

What you'll need:

Collection

Stripwood

Time Required

Planning: 2 hours
Sawing & Fiting:1 hour

Tools Required

  • 12 x 96 x 2400mm Pine Stripwood
  • Tape Measure 
  • Pencil 
  • Paper
  • Laser Level 
  • Ladder
  • Saw
  • Mitre Box
  • Sandpaper
  • Grab Adhesive*
  • Nail Gun 
  • Nails
  • Decorators Caulk
  • Paint 
  • Primer**
  • Paint Brush
  • Paint Roller

Safety

As a precautionary measure use a pipe and cable detector before nailing or drilling to check there are no hidden pipes or electric cables. For safety wear protective gloves, glasses and knee pads. When using a mitre box it’s always a good idea to fix the box to a secure surface, to allow for both hands to be free when sawing. Ensure you do not drill directly above or below light switches and power sockets. Be sure to follow manufacturer’s instructions when using all tools and materials.

*Be sure to follow your chosen adhesive’s instructions, you may need to ventilate the room. **May be needed if your chosen paint requires primer

 

A step-by-step guide to creating a feature wall within your home, using Richard Burbidge mouldings and basic woodworking tools and techniques.

There are hundreds of different designs you can create with wall panelling, in this guide we are going to be showing you how to install the classic but contemporary square panel design that goes from floor to ceiling, to create a feature wall.

1. Planning and measuring

Planning is the most time consuming, but also the most important step of the whole process. Firstly, you will need to measure the walls every length and width, making a note of any fittings and fixtures you will need to avoid. Draw your design with the measurements on some paper, making sure to plan an equal gap horizontally and vertically. The next step is to transfer your measurements and plan to the wall, using a pencil, tape measure and laser level, mark where each panel piece will be, while bearing in mind the width of the panel. We also recommend removing skirting and architrave on the feature wall to achieve a professional finish.

2. Choose your Richard Burbidge moulding

Richard Burbidge mouldings are of the highest quality and can totally transform the look and character of a whole room. Our stripwood range has a vast selection of panel sizes to choose from. For this project we are using STW6027 which is a 12 x 96 x 2400mm pine panel that creates the classic square feature wall you will have seen everywhere on Pinterest and Instagram!

3. Cut the panels to length

The next step is to cut your panels to length. Our stripwood mouldings are 2400mm in length which is the average height of most rooms, so you won’t need to cut the mouldings that are being placed vertically. Using a saw and mitre box at a 90 degree angle, carefully cut the panels that will be horizontally placed according to the measurements you noted from step 1. Repeat this process to all of the horizontal panels, then lightly sand the ends until smooth. If your wall is not 2400mm in length then you will need to cut the moulding according to your walls measurements using this same method.

4. Apply panels to the wall

When applying the panels to the wall start with the vertical panels, then the horizontal panels. To apply the panels to the wall we recommend nails and adhesive for that extra security and hold. Place your panel onto the wall where you marked out in step 1, use a laser level to ensure the panel is straight, then apply strong hold adhesive to the back and apply to the wall, next use a nail gun to fully secure the panel to the wall. Repeat this process for all panels.

Ensure you use a pipe and cable detector before nailing or drilling into any walls. If you are unsure if it is safe to nail into your wall, opt for a strong adhesive instead.  Once you have applied the panels, use decorators caulk to patch any gaps, cracks, or holes, then sand prior to finishing.

5. Add your own creative flare

This project can be customised to work with any décor and colour scheme. There are many different ways you can add your own creative flare to this project. You can choose to paint the whole wall one colour, or you can use a few different paint colours, paint dots, stripes or squares, or even draw your own unique design to really make this wall the focal point of your home. There’s an endless list of ways that you could choose to add your own creative flair.

6. Share your DIY renovation project

We love seeing how you have transformed your home with Richard Burbidge. Upload a picture of your DIY project to Instagram or Facebook and tag us @richard_burbidge. You can also upload your images to our testimonials page here. We can’t wait to see what you create with Richard Burbidge mouldings!

 

Need help? Get in touch with us today

contact us

Search our product catalogue